1853 C Sherman Dr. Professional White Rubber Roof: Com plete Installation Kit – 3,400 sq. First Rate Materials – WHITE 60 Mil EPDM Rubber & Bonding Adhesive. Quality Products – Includes Seam Tape, Flashing Tape, Primer, Caulk, & T-Bars. 1 – count 20′ x 100′ 60 Mil EPDM WHITE Rubber Roofing Roll====800 lbs. 1 – count 20′ x 70′ 60 Mil White EPDM Rubber Roofing Roll====560 lbs. 9- count 4 Gallon Pails Latex Bonding Adhesive. 2 – count 3 x 50′ black Seam Tape. 4 – count 1 pint Can Seam Primer/Activator. 2 – count 6 x 50′ White Uncured tape Flashing. 30 count 10′ x 1 Aluminum T-bars. 5 Tubes WHITE Lap Sealant Roofing Caulk. Method of Applying EPDM with heavy bodied latex bonding adhesive and 3. Seam tape application as required. Clean the roof surface of all debris and nails. Re-fasten any loose roof boards. Fill any gaps larger than 3/8 inch with wooden strips. The EPDM cannot span gaps of more than 3/8 without risk of possible adhesion issues. Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane. Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Slowly fold the EPDM roofing membrane back into place while the adhesive is tacky and moist, and NOT still totally wet. This takes 10 to 15 minutes normally depending on your weather conditions. Please be aware NOT to lay the EPDM into WET adhesive but damp and tacky. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane. Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3 seam tape if required to splice 2 pieces of EPDM deck sheet together. Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof. Seam tape application if required to join 2 sheets together. Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet. Clean and/or prime the seam area of both rubber sheets using EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area. Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2 out from the edges of the bottom sheet. Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam. With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape. Remove the paper backing by pulling out from under the top sheet at a 45º angle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. Structodek with Primed Red Coating. As an insulation board, coverboard or re-roof/recover board, Structodek High-Density Roofing Board is the answer for low-slope applications and systems. STRUCTODEK INSULATION RECOVERY BOARD 4′ X 8′, 1/2 THICK 64 LBS PER SQUARE 3 – 4′ X 8′ BOARDS PER SQUARE (100 SQUARE FEET) NOTE 30.4 SQUARES CAN BE ON A PALLET. 3 BOARDS 96 SQUARE FEET==95 PIECES PER PALLET===2,000 lbs per Pallet=729.6 SQUARES PER TRUCK, 24 PALLETS. STRUCTODEK® HIGH DENSITY (HD). FIBERBOARD ROOF INSULATION COVER BOARD WITH PRIMED RED COATING. The proprietary, patent pending, non-asphaltic Primed Red Coating integrated on the surface of STRUCTODEK HD possesses unique bonding characteristics that ultimately result in superior adhesion capabilities with the current membrane & adhesive technology on the market today. The nonasphaltic Primed Red Coating is compatible with all single-ply membranes including PVC, TPO, EPDM, and CSPE without concern of premature membrane degradation that is often associated with asphalt emulsion coated fiberboard products. Additionally the Primed Red Coating, unlike asphalt emulsion coated products, has proven to be compatible with traditional, low VOC and water-based adhesives as well as many foam adhesives. The Primed Red Coating allows adhesives & foams to key into the STRUCTODEK HD surface while at the same time deterring excessive adhesive absorption. The unique Primed Red Coating allows for a solid membrane bond while still providing optimal square foot per gallon of adhesive coverage thus insuring a quality & cost effective membrane installation. Lottes Roofing 1853 C Sherman Dr. Our Technicians can design and determine what you need for your roofing project and give you a complete estimate for your materials as well as instruct you about your installation process! This Product is a Professional Grade EPDM Rubber Roof Installation Kit. Flashing detail, seam flaps, & roof penetrations will determine actual roof coverage. Please allow for these adjustments when purchasing materials. Summary of Lottes Roofing Policies. Time tables will vary depending on the items ordered. The free listing tool. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item. The item “3,400 sq ft WHITE 60 mil EPDM Rubber Roofing Kit COMPLETE” is in sale since Thursday, December 3, 2015. This item is in the category “Business & Industrial\Building Materials & Supplies\Contractor Guides & Manuals”. The seller is “thelottescompaniesstore” and is located in Saint Charles, Missouri. This item can be shipped to United States.
- Country/Region of Manufacture: United States
- Brand: lottes